作者:潘建强, 盛振新, 毛海斌, 刘建湖, 张显丕
作者单位:中国船舶科学研究中心, 江苏 无锡 214082
关键词:预制飞片圆筒;水下爆炸;近药包表面能量;测试技术
摘要:
为测量水下爆炸条件下近药包表面的能量,提出基于预制飞片圆筒的水下爆炸条件下近药包表面能量测试技术。首先,采用AUTODYN软件,对水下爆炸条件下自由场和作用在飞片上的能流密度进行数值计算,通过对比两者随爆距的变化规律,对预制飞片圆筒间接获取近药包表面能量的可行性进行论证。然后,采用激光位移传感器和探针测量爆炸后的飞片速度,进而将飞片的动能除以面积计算得到作用在飞片上的能流密度。将能流密度的测试值与计算值进行对比,两者基本一致,表明采用预制飞片圆筒来测量水下爆炸条件下近药包表面的能量是可行的,同时验证飞片速度测量系统的有效性,为近药包表面载荷特性的理论研究和试验测试提供技术基础。
Research on the measurement technology of energy near the charge for underwater explosion
PAN Jianqiang, SHENG Zhenxin, MAO Haibin, LIU Jianhu, ZHANG Xianpi
China Ship Scientific Research Center, Wuxi 214082, China
Abstract: In order to measure the energy near the charge surface for underwater explosion, a pre-grooved cylinder was proposed to measure the energy near the charge. At first, the energy density in the free field and on the flyer were calculated with AUTODYN, the changes in energy density as distance changes were compared, which demonstrated the feasibility of energy measurement with pre-grooved cylinder. Then, the laser displacement sensor and probe were used to measure the flyer velocity. Based on the velocity, the energy density on the flyer could be calculated. Then, the measured energy density on the flyer and energy density in the free field were compared, and they were found accordant. The results prove that the pre-grooved cylinder could be used to measure the energy near the charge surface, which could provide technology support for theoretical research and experiment measurement of underwater explosion load characteristics near the charge.
Keywords: pre-grooved cylinder;underwater explosion;energy near the charge;measurement technology
2016, 42(10): 1-8 收稿日期: 2016-4-13;收到修改稿日期: 2016-5-25
基金项目: 国家自然科学基金项目(51409234)
作者简介: 潘建强(1971-),男,江苏丹阳市人,研究员,硕士,主要从事爆炸与冲击测试技术研究。
参考文献
[1] MANFRED H. Impulse method for the blast contour of cylindrical high explosive charges[J]. Propellants Explosives Pyrotechnics,1999(24):17-26.
[2] 赵继波,谭多望,李金河,等. TNT药柱水中爆炸近场压力轴向衰减规律[J]. 爆炸与冲击,2008,28(6):539-543.
[3] COLE. 水下爆炸[M]. 罗耀杰,韩润泽,官信,等,译. 北京:国防工业出版社,1960:97-104.
[4] 谭成文,王富耻,李树奎,等. 内爆炸加载条件下圆筒的膨胀、破裂规律研究[J]. 爆炸与冲击,2003,23(4):305-308.
[5] 王迎春,李树奎,王富耻. 内爆炸载荷下钨含量对W-Ni-Fe高密度合金圆筒膨胀过程的影响[J]. 稀有金属材料与工程,2008,37(3):424-454.
[6] 范亚夫,段祝平,马岳,等. 钛合金TC4材料热处理工艺对圆筒在内爆炸载荷下膨胀半径的影响[J]. 爆炸与冲击,2004,24(4):337-346.
[7] 刘宏利,邵磊,贾明雁,等. 激光多普勒效应在爆炸冲击测量中的应用研究[J]. 振动与冲击,2008,27(1):97-98.
[8] LEE E, BREITHAUPT D, MCMILLAN C, et al. The motion of thin metal walls and the equation of state of detonation products:UCRL-91490[R]. 1985.
[9] BAUDIN G, BERGUES D. A reaction model for aluminized PBX applied to underwater explosion calculation[A]//Tenth Symposium (international) on Detonation[C]//Massachusetts Boston:[s.n.],1993:646-655.
[10] 陈朗,李泽仁. 激光速度干涉仪测量法在炸药圆筒试验中的应用[J]. 爆炸与冲击,2001,21(3):229-232.