作者：王晓光, 刘柯, 郭天茂, 鲍晨兴, 王锴磊

作者单位：北京航天计量测试技术研究所，北京 100076

关键词：焊接残余应力;光栅扫描;轮廓法;应力云图

摘要：

目前测量焊接残余应力的轮廓法都是采用三坐标机对被测件切割面轮廓进行测量，但三坐标机的测量过程是逐点测量，测量效率低、测点少，该文针对这一问题，提出一种基于高精度光栅扫描测量切割面轮廓的轮廓法。以Q235板材为被测对象，对其焊接残余应力进行测量。首先，采用高精度光栅扫描仪对Q235板材切割面轮廓进行测量；其次，从测量得到的海量点云中提取了轮廓节点数据；再次，进行应力重构，得到板材在该截面处的法向残余应力云图；最后，将得到的测量结果与基于三坐标机测量的轮廓法测量结果进行对比，偏差在50 MPa以内，论证该文方法有效。实验结果表明：该方法具有测量精度高、速度快、测点多的优点，能够满足焊接残余应力测量的需求。

Research on contour method measurement technology of welding residual stress based on grating scanning
WANG Xiaoguang, LIU Ke, GUO Tianmao, BAO Chenxing, WANG Kailei
Beijing Aerospace Institute for Metrology and Measurement, Beijing 100076, China
Abstract: At present, the contour method of measuring welding residual stress is to measure the contour of the cutting surface by CMM, but the measurement process of CMM is point by point measurement, therefore, the measurement efficiency is low and the measurement points are few. In order to solve this problem, a method of measuring the cutting surface contour based on high-precision grating scanning is proposed. In this paper, the welding residual stress of Q235 plate is measured. Firstly, the cutting surface contour of Q235 plate is measured by this method. Secondly, the contour node data is extracted from the measured massive point cloud. Thirdly, the normal residual stress nephogram of the plate at the section is calculated. Finally, the experimental results obtained by this method are compared with the experimental data of contour method based on CMM to verify the accuracy of the method of this paper. The deviation is less than 50 MPa. The experimental results show that the method has the advantages of high precision, high efficiency and large amount of measurement data, and can meet the requirements of welding residual stress measurement.
Keywords: welding residual stress;grating scanning;contour method;stress nephogram
2022, 48(12):35-39  收稿日期: 2021-06-27;收到修改稿日期: 2021-09-05
基金项目:
作者简介: 王晓光(1990-),男,河北张家口市人,工程师,硕士,主要研究方向为光学测量、精密仪器
参考文献
[1] 陈尧, 陈昌华, 汤志贵, 等. 锻件表面残余应力的盲孔法测试与分析[J]. 物理测试, 2015, 33(6): 24-30
[2] 马小明, 欧清扬. 反向钻孔法应用于工件内表面残余应力测量的研究[J]. 中国测试, 2019, 45(5): 26-32,37
[3] 潘龙, 邓楚铨, 徐振钦. 基于传递矩阵的钻孔应变法测量薄板残余应力[J]. 中国测试, 2021, 47(1): 36-41+48
[4] 张定铨, 何家文. 材料中残余应力的X射线衍射分析和作用[M]. 西安: 西安交通大学出版社, 2000.
[5] 张峥. 飞机弱刚性铝合金结构件的残余应力和加工变形控制技术研究[D]. 南京: 南京航空航天大学, 2016.
[6] PRIME M B. Cross-sectional mapping of residual stresses by measuring the surface contour after a cut[J]. Journal of Engineering Materials and Technology, 2001, 123(2): 162-168
[7] 铁摩辛柯, 古地尔. 弹性理论[M]. 徐芝纶, 译. 北京: 高等教育出版社, 1990.
[8] 詹旭. 点云数据预处理之关键算法研究[D]. 绵阳: 西南科技大学, 2021.
[9] 张玉存, 李亚彬, 付献斌. 基于曲率约束的点云分割去噪方法[J]. 计量学报, 2020, 41(10): 1218-1225