作者：郭栋梁, 刘新妹, 殷俊龄, 陈云
作者单位：中北大学电子测试技术国家重点实验室, 山西 太原 030051
关键词：自动故障诊断系统;数据采集;矩阵开关;通用电路板接口;LabVIEW
摘要：
针对传统电路板测试的局限性与单一性以及日趋灵活的电路板测试需求，基于矩阵开关技术、自动测试技术和虚拟仪器技术，设计并实现一种通用电路板自动故障诊断系统。该系统基于PCI总线技术所构建的通用硬件框架以及利用LabVIEW实现的上位机软件，实现通用电路板的直流电平测试、静态参数测试以及动态参数测试等，完成测量结果的对比分析、保存以及故障定位。实验证明：该系统能够快速准确地完成通用电路板的测试任务。系统搭建完成后，进行7次独立重复试验，测试结果显示：该系统测试数据的最大误差为0.3%，同时具有性价比高、通用性好、可靠性高等优点，并且可以大大提高测试效率。
Design and implementation of common circuit board automatic fault diagnosis system
GUO Dongliang, LIU Xinmei, YIN Junling, CHEN Yun
National Key Laboratory for Electronic Measurment Technology, North University of China, Taiyuan 030051, China
Abstract: This is an automatic fault diagnosis system for common circuit board based on matrix switch, automatic test and virtual instrument technologies, designed according to the limitations and unity of traditional circuit board test and an increasingly flexible test tendency. The system realizes DC level test, static and dynamic parameter tests of common circuit board, and performs comparative analysis and preservation of measurement results and fault location by the help of common hardware testing framework built by PCI bus technology and upper computer software achieved by LabVIEW. Experiment results have proven that the system is able to perform common circuit board test fast and accurately. There were seven independent repeated trials after the system was established. Results show that the maximum error of test data is ±0.3%. Together with advantages such as high cost performance, universality and reliability, the test efficiency is greatly raised.
Keywords: automatic fault diagnosis system;data acquisition;matrix switch;common interface of circuit board;LabVIEW
2016, 42(7): 112-116 收稿日期: 2015-11-17;收到修改稿日期: 2015-12-28
基金项目:
作者简介: 郭栋梁(1987-),男,江苏徐州市人,硕士研究生,专业方向为测控技术。
参考文献
[1] 贾娜,王红萍,戴军. 自动测试系统的发展现状和前景[J].科技与企业,2015(9):85.
[2] 王和明,王菊. 浅谈自动测试系统的发展与不足[J]. 飞航导弹,2014,6(1):59-61.
[3] 屈建兵. 军用自动测试系统的发展综述[J]. 直升机技术,2014(1):59-64.
[4] 贾国龙,陈思平,赵文龙. 一种通用的电路板自动测试系统的设计与实现[J]. 科技情报开发与经济,2009(5):150-153.
[5] ZHENG W, LIU R, ZHANG M, et al. Design of fpga based high-speed data acquisition and real-time data processing system on J-text tokamak[J]. Fusion Engineering and Design,2014,66(23):586-589.
[6] PATEL J J, REDDY N, KUMARI P et al. Embedded Linux Platform for Data Acquisition Systems[J]. Fusion Engineering and Design,2014,89(5):684-688.
[7] 常高嘉,冯全源. 基于FPGA的高速数据采集系统的设计与实现[J]. 电子器件,2012(5):615-618.
[8] 于雪莲. 基于FPGA的高速数据采集系统的设计[D]. 保定:河北大学,2014.
[9] 姜伟,刘新妹,殷俊龄,等. 用于自动测试系统继电器矩阵开关的设计[J]. 计算机测量与控制,2012(12):3368-3369.
[10] HUMBLA S, KALEEM S, MULLER J, et al. On-orbit Verification of a 4×4 Switch Matrix for Space Applications Based on the Low Temperature Co-fired Ceramics Technology[J]. Frequenz,2012,66(11):355-362.
[11] HASHEMI S, AZGHADI M R, ZAKEROLHOSSEINI A, et al. A Novel Fpga-programmable Switch Matrix Interconnection Element in Quantum-dot Cellular Automata[J]. International Journal of Electronics,2015,102(4):703-724.
[12] 刘伟. 印刷电路板的智能检测系统研究[D]. 北京:中国地质大学,2013.
[13] 郭甲阵,谢华,兰京川. 基于虚拟仪器的雷达电路板自动测试系统[J]. 仪表技术与传感器,2011(2):26-28.
[14] 王琪. 基于Virtools技术的自动变速器虚拟仿真故障诊断系统的开发[D]. 长春:吉林大学,2013.
[15] 叶小杰. PCI数据采集卡的设计及测试方法研究[D]. 成都:电子科技大学,2011.
