作者：欧阳凯, 黄慧娟, 韩梁, 胡鹏浩

作者单位：合肥工业大学仪器科学与光电工程学院, 安徽 合肥 230009

关键词：并联坐标测量机;测量误差;误差模型;杆长误差

摘要：

在并联坐标测量机中，杆长误差是主要的误差源之一。结合所研发的3-PUU并联坐标测量机，通过建立测量误差模型，从理论及仿真角度分析杆长误差所引起的测头运动误差，进一步分析各坐标方向的测头运动误差对样机测量精度的影响。在此基础上设计专门的实验，实验结果表明，杆长误差引起的动平台位置、姿态误差对测量误差的影响度不同，并且位置、姿态误差转变的测量误差分量之间在工作空间内不同位置并非呈现单一误差累积或者误差平均，在不同坐标方向上测量误差的分布规律也不同。

Analysis of the effect of bar length error on probe motion error of parallel coordinate measuring machine
OUYANG Kai, HUANG Huijuan, HAN Liang, HU Penghao
School of Instrument Science and Opto-electronics Engineering, Hefei University of Technology, Hefei 230009, China
Abstract: Bar length error is one of the main error sources in parallel coordinate measuring machine as well as in other parallel mechanism, which will be discussed further with self-developed 3-PUU parallel coordinate measuring machine in this paper. The motion error of the probe on the moving platform caused by the bar length error is revealed based on the established measurement error model, and the influence of the motion error of each coordinate direction on the measurement accuracy is also analyzed. Finally, a special experiment was designed, the following experimental results show that the position and orientation errors of the moving platform caused by the bar length errors in the workspace have different effects on the measurement errors in different coordinate directions, and the measurement error components transformed by the position and orientation errors do not present single error accumulation or error average in different positions, and the distribution of measurement error components in different directions are not same.
Keywords: parallel coordinate measuring machine;measurement error;error model;bar length error
2020, 46(6):27-33  收稿日期: 2019-12-03;收到修改稿日期: 2020-01-10
基金项目: 国家自然科学基金项目(51775163，51475133)
作者简介: 欧阳凯(1994-),男,湖南邵阳市人,硕士研究生,专业方向为精密仪器及机械
参考文献
[1] HU P H, YU C W, FAN K C, et al. Error averaging effect in parallel mechanism coordinate measuring machine[J]. Applied Science, 2016, 6(12): 383-395
[2] 王启明, 张辉, 汪劲松, 等. FAST馈源精调试验平台运动精度分析[J]. 机械工程学报, 2002, 38(S1): 52-55
[3] 单鹏, 谢里阳, 田万禄, 等. 基于D-H矩阵的Stewart型并联机床位姿误差计算模型[J]. 机械工程学报, 2010, 46(17): 186-191
[4] MIKHAEL T, STEPHANE C, ALEXANDRE G, et al. Sensitivity analysis of parallel manipulators using an interval linearization method[J]. Mechanism and Machine Theory, 2014, 71: 93-114
[5] 孟婥, 车仁生. 并联六坐标测量机的误差模型和误差补偿[J]. 哈尔滨工业大学学报, 2004, 36(3): 317-320
[6] 陈修龙, 赵永生, 邓昱. 新型并联机器人坐标测量机误差建模与仿真[J]. 计算机集成制造系统, 2008, 14(3): 477-481
[7] 朱小蓉, 沈惠平. 一种新颖并联运动坐标测量机的误差建模与仿真[J]. 中国制造业信息化, 2006, 35(17): 56-60
[8] RUGBANI A, SCHREVE K. The kinematics and error modelling of a novel micro-CMM[J]. The International Journal of Advanced Manufacturing Technology, 2015, 78(5-8): 961-969
[9] 黄真, 孔令富, 方跃法. 并联机器人机构学理论及控制[M]. 北京: 机械工业出版社, 1997.